Description
Details
524WiFi™ P7915DAN-2x2-DBDC-MP-MMCX Pro Plus — MediaTek MT7915DAN Wi-Fi 6 2x2 Dual-Band Concurrent Mini PCIe AP Module with MMCX, 2.4 + 5 GHz
Build a dual-band Wi-Fi 6 access point around robust MMCX antenna connections. The AX1800-class Mini PCIe module delivers concurrent 2.4/5 GHz operation with two spatial streams per band, suited to enclosed gateways, custom RF cabling and professional integration projects.
524WiFi™ Pro Plus — tuned for your wireless deployment
Our Pro Plus radio modules are tuned for their intended wireless applications. Combine the radio architecture specified for this model with the right host, software configuration and antenna system to get the most from your installation. Model-specific specifications and integration guidance help you choose the right configuration.
524WiFi™ Signal Plus™ — make the most of your RF path
Signal Plus™ brings the antenna, operating band, polarization, connectors and installation together as one RF system. Match the antenna coverage to your application and keep the feed path short and low-loss to preserve useful signal in both directions. This model is part of our tuned product range; use its specified RF connector layout and supported bands when building your Signal Plus™ installation.
A matched host, client and antenna system helps deliver the performance suited to your installation. Choose antennas and cabling for this card through 524WiFi™; select the accessories listed for your chosen configuration.
Where this module fits
Rugged routers, vibration-prone installations, test fixtures and outdoor enclosures where positive-retention MMCX cabling is preferred over micro-coax snap connectors.
Technical specification
| Wireless generation | Wi-Fi 6 (802.11ax) |
|---|---|
| Performance class | AX1800; theoretical PHY performance class. |
| Radio layout | 2×2 at 2.4 GHz plus 2×2 at 5 GHz, DBDC |
| Supported bands | 2.4 GHz and 5 GHz concurrently |
| Channel widths | 20/40 MHz at 2.4 GHz; 20/40/80 MHz at 5 GHz |
| Host form factor | full-size Mini PCIe |
| Host interface | PCIe |
| RF connectors | 2 × dual-band MMCX RF connectors |
| Silicon platform | MediaTek MT7915DAN |
| Linux driver family | Linux mt76 / mt7915e |
| Power design | 3.3 V ±5%; 3 A host supply recommended |
| Mechanical envelope | 30 × 50.95 mm class; verify keep-out area and mounting screw position against the host drawing. |
| Environmental range | Operating −30 to +70 °C in a dry, condensation-free environment. |
P7915DAN-2x2-DBDC-MP-MMCX engineering notes: radio, host and real deployment
Radio architecture and application
Build a dual-band Wi-Fi 6 access point around robust MMCX antenna connections. The AX1800-class Mini PCIe module delivers concurrent 2.4/5 GHz operation with two spatial streams per band, suited to enclosed gateways, custom RF cabling and professional integration projects.
P7915DAN-2x2-DBDC-MP-MMCX — PHY rate by radio configuration
2.4 GHz / 40 MHz / 2 streams: 573 Mbit/s
5 GHz / 80 MHz / 2 streams: 1201 Mbit/s
Deployment design for Mini PCIe / MMCX
Choose this version for fixtures or enclosed gateways whose cabling is already designed around MMCX. Keep cable bends clear of the card; enclosure-mounted bulkhead connectors carry external cable loads. Compare both band RSSI readings after assembly to catch a damaged or mismatched pigtail.
OpenWrt driver and firmware selection
Package/stack reference: kmod-mt7915e + kmod-mt7915-firmware. Software packages are selected for the installed OpenWrt release and target platform. Matching release-specific packages align the driver with the running kernel ABI. Use kernel modules built for the installed system image. The complete software configuration combines the driver, firmware, calibration data and selected radio profile.
Check PCI enumeration first, then firmware loading, then the PHY capabilities and finally hostapd configuration. On minimal images, lspci and iw may need their respective utilities installed. Keep the working image and configuration before changing the software stack. Preserve the radio’s original device-specific EEPROM and calibration data.
lspci -nnk uname -r dmesg | grep -Ei "mt76|mt79|mt7615|firmware|pci" iw phy iw reg get iw dev logread | grep -Ei "hostapd|wlan|firmware"
In iw phy , confirm AP interface support, band frequencies, channel widths and valid interface combinations. Use iw dev to identify the interface names assigned by the installed image. Use iw dev INTERFACE station dump with the real AP interface to inspect per-client rates, signal and retries. A missing PHY after successful PCI enumeration points toward driver/firmware initialization rather than the antenna cable.
RF budget and fault isolation
Antenna gain, cable attenuation and legal conducted power form one link budget. In simplified dB terms, EIRP equals radio output plus antenna gain minus feed loss; a higher-gain antenna may require lower radio output under the applicable limit. A balanced two-way link combines suitable antennas with the transmit capability at both ends. Per-chain RSSI and retry statistics help tune antenna placement and permitted transmit power.
For instability under traffic, capture logs before rebooting and compare a cold open-bench test with the closed enclosure. Check supply droop, thermals, firmware resets and the wired uplink. If only wider channels fail, investigate interference, channel availability and client capability before replacing the hardware. For remote sites, retain a wired management or recovery path while qualifying wireless changes.
Configuration documentation and support
Use the OpenWrt wireless configuration guide for general configuration. Revision-specific files and assistance remain through 524WiFi™ Downloads & Support . Send the model code, PCB revision, host, country, exact image/kernel version and sanitized diagnostic logs.
Linux, OpenWrt, firmware and board data
The module uses the Linux mt76 / mt7915e stack. Successful enumeration requires a real PCIe connection, sufficient 3.3 V power, a kernel/mt76 combination supporting the silicon generation, matching firmware and—where the platform requires it—the correct board-data/calibration file. Select firmware and BDF files for the exact hardware revision.
- Confirm the PCIe device appears with
lspci -nnbefore debugging the wireless stack. - Review
dmesg | grep -Ei 'mt76|mt79|firmware|pci'for firmware, reset, IOMMU and memory-allocation messages. - Verify loaded modules with
lsmod | grep -E 'mt76|mt79'. - Use
iw phyandiw reg getto confirm supported bands, channel widths and the active regulatory domain.
Use our 524WiFi™ Downloads & Support area for model-specific software guidance. Contact support with the 524WiFi™ model code, PCB revision, host board, kernel/OpenWrt release and a complete boot log when a revision-specific package is required.
Installation checklist
- With the host powered off and ESD precautions in place, install the card in a slot wired for PCIe.
- Check the 3.3 V rail against the stated power budget and provide airflow or a correctly fitted heatsink for sustained AP traffic.
- Seat the card squarely, install the mounting screw and keep metalwork away from components and antenna connectors.
- Attach all required RF paths using the exact connector type: 2 × dual-band MMCX RF connectors. Connect and disconnect micro-coax vertically with the proper tool.
- Boot with a supported kernel/firmware set, check PCIe enumeration, then configure country, channel, bandwidth and transmit power legally.
- Run load and temperature tests before closing the enclosure or deploying remotely.
Signal Plus™: antenna and RF-path integration
Signal Plus™ is the 524WiFi™ selection path for matching the correct number of pigtails, low-loss feed length and antennas to the radio layout. Match the complete RF system to the installation and operating country. For this model start from 2 × dual-band MMCX RF connectors and 2.4 GHz and 5 GHz concurrently. Keep coax runs short, maintain connector separation and use antennas approved for the intended bands and country.
Browse internal RF pigtails and MIMO antennas, then ask us to verify the connector and band combination before ordering a complete RF set.
Configuration guidance
| PCIe device detection | Check that the socket carries PCIe, inspect reset timing, seating, power rail and BIOS/device-tree configuration. |
|---|---|
| Firmware setup | Match the firmware and board-data files to this card’s driver and hardware revision. |
| Radio and band configuration | Check the selected radio mode, firmware, country code, antenna mapping and whether the model is DBDC or selectable-band. |
| Stable operation under traffic | Measure 3.3 V droop and temperature, add cooling, shorten RF feeds and review PCIe/IOMMU errors. |
| Throughput configuration | Verify negotiated channel width, client stream count, interference, antenna polarization, regulatory power and CPU/network bottlenecks. |
FAQ
What platforms is this card designed for?
Embedded access points, Linux gateways and specialist networking hosts with the specified PCIe interface, power supply and RF connections.
What does Pro Plus bring to this product?
A tuned professional radio platform with model-specific integration guidance, RF-system selection and access to our technical support.
Does Signal Plus™ include antennas?
Choose the antenna and pigtail set listed for your ordered RF kit. Use our antenna and pigtail links to build a verified set.
Can 524WiFi™ supply firmware?
Model-specific firmware guidance is available through our technical support. Linux/OpenWrt packages provide the software path, complemented by the appropriate board data for the host and hardware revision.
What information should I send for compatibility review?
Send the exact 524WiFi™ model code, host board, slot wiring or schematic, available 3.3 V current, kernel/OpenWrt version, intended bands/country, enclosure and antenna plan.
Technical model and configuration
P7915DAN-2x2-DBDC-MP-MMCX : MediaTek MT7915DAN; MediaTek MT7915DAN Wi-Fi 6 2x2 Dual-Band Concurrent Mini PCIe AP Module with MMCX, 2.4 + 5 GHz. The model identifies the platform, radio configuration, supported bands and the relevant form factor or wired interface.
Features:
- 2T2R in 2.4 GHz+2T2R in 5G with support of up to 573+1201Mbps PHY rate
- Channels Bandwidth: Supports 20, 40, 80 channels
- HE MCS0-11 BW20/40/80MHz with Nss=1~2
- Short Guard Interval Support
- Space-time block codes(STBC) and Low density Parity check (LDPC)
- Support digital pre-distortion to enhance PA performance
- Smoothing (channel estimation) extension to MIMO case
- DFS radar detection
- Embedded ARM Cortex R4 processor for full host CPU offload
- Microprocessor: Embedded 32-bit RISC
- Beamformer: Decoded BW20/40/80 up to 2×2 BF matrix apply
- Beamformee:Decoded BW20/40/80 up to 4×2 MU matrix feedback
- Modes: Greenfield, mixed mode, legacy modes support
- Highly integrated RF: with 40nm low power process
- Noise mitigation: Supports background scan function for fast channel switching
- Supports spectrum analysis for non-Wi-Fi signals
- Intelligent power saving
- WFA WMM, WMM PS (QoS)
- Integrate high efficiency: internal 2.4GHz/5GHz PAs
- Intelligent Calibration (iCal): reduces the production time
Standard
| Standards | Wireless: IEEE 802.11ax/ac/b/g/n (2Tx2R) |
|---|---|
| Data Rate | IEEE802.11ax 1201Mbps @TX/RX IEEE802.11ac 1733Mbps @TX/RX IEEE802.11a/n 600Mbps @TX/RX IEEE802.11a/g 108Mbps IEEE802.11b 22Mbps |
| Output Power | 11b: 23dbm+/- 1.5dbm @11Mbps 11g: 20dbm+/- 1.5dbm @54Mbps 11g/n: 20dBm +/- 1.5dbm @MCS7, HT20 17dBm@MCS7,HT40 11a: 19.5dBm +/- 1.5dbm @54Mbps 11a/n: 19.5dBm+/- 1.5dbm @MCS7, HT20 17dBm@MCS7, HT40 11ac HT20: 20+/-1.5dBm @MCS8 11ac HT40: 17+/-1.5dBm @MCS9 11ac HT80: 14.5+/-1.5dBm @MCS9 11ax HT20: 20+/-1.5dBm @MCS9 11ax HT40: 17 +/- 1.5dBm @MCS9 11ax HT80: 14.5 +/- 1.5dBm @MCS11 |
| Certification | CE, FCC , IC , NCC |
| Receiver Sensitivity | 11b: -99dBm @11Mbps 11g: -95dBm @54Mbps 11g/n: -90dBm @HT20, MCS7 -86dBm @HT40, MCS7 11a: -90Bm @54Mbps 11a/n: -85dBm @HT20, MCS7 -81dBm @HT40, MCS7 11ac: -90dBm +/- 2dBm @VHT20 MCS8 11ac: -85dBm +/- 2dBm @VHT40 MCS9 11ac: -68dBm +/- 2dBm @VHT80 MCS9 11ax: -61dBm +/- 2dBm @HE20 MCS11 11ax: -58dBm +/- 2dBm @HE40 MCS11 11ax: -55dBm +/- 2dBm @HE80 MCS11 |
| Antenna | External Antenna connector (MMCX) x2 |
| Frequency Range | US, Canada 2.412GHz~2.462 GHz (CH1~CH11) EU, Japan: 2.412GHz~2.472GHz (CH1~CH13) 5.15GHz ~5.875GHz |
| Security | Security: 64/128-bit WEP Encryption, WPA, WPA2 Driver: Linux |
| Operating Voltage | DC 3.3V ± 5% |
| Temperature | Operating: -30°C ~ +70°C Storage : -30°C ~ +90°C |
| Humidity | Operating Humidity: 10%~90% non-condensing Storage Humidity: 10%~90% non-condensing |
| Dimension | 50.95(H) x 30(W)mm |
| Power consumption | maximum is 9W, average is 4 – 8W. |
| Main board Power Supply | design please provide 3.3V 3A, minimum 3.3V 2.5A. |
Additional
Additional Information
| Brand | 524WIFI |
|---|---|
| firmware | No |
Tags
Reviews
Having a questiion ?? Contact us - info at 524wifi.com !!


