Wodaplug ® Dual SIM 5G 5GNR 4G LTE-A dual modules Failover redundancy & Load balance Open Source router MTK7621 board HW version 7 and higher, 4x LAN 1xWAN, 12 antenna ports, standalone: 1xM.2 USB3, 3xMiniPCIe, H721v5G can support 11ac WiFi (11ac 600VX or 900VX module ready, MT7915 based 11ax WiFi 6 modules supported in new firmware). New version 7 comes with 2.4G wifi module (Transytem TWL-2301H TWL-103  - Based on Atheros AR9590 3x3 MIMO Platform).

The H721 v5G Dual sim 5G LTE router with 4 standalone modules slots has been a great choice for custom builds and applications.  The router board’s (PCB) built in 1x M.2 slot for LTE modem and 2x SIM Card slots, makes it a great fit for our line of Sierra Wireless  Quectel M.2 modems. Also have 3 x Minipcie slots, 1 x for aditional modem (it is our M.2 B-Key adapter compatible) and 2 x more for your old standard modem (save your investment) or new one smoking gun in wifi world like 600vx / 900vx QCA9880 miniPCIe modules and WiFi 6 MT 7915/ 7916 modules (in new X-WRT firmeare).

Our new inventory of H721 v5G routers were special ordered to better accommodate our customer’s needs. New improved 5G ready version 7! Once again, if you want to have all info about ETA, versions,etc pls check our facebook page for news !

The H721 v5G now includes:

• 4 x 5G LTE Antennas + 4 x MHH4 pigtails for LTE modules pre-installed
• 3 x WiFi  Antennas + 3 x U.FL to SMA Bulkhead Antenna Connector Pigtails (pre-installed). 
• 2,4GHz WiFi 802.11n miniPCIe module (Transytem TWL-2301H TWL-103 - Based on Atheros AR9590 3x3 MIMO Platform ) - you can install second wifi module for dual radio application
• 12 Volt 2Amp Power Adapter
• 6 x Screws, Spacers/Nuts to mount M.2 LTE modem
• Wall mounts, screws and lags
• Cat5e Ethernet Cable
• THIS ROUTER IS NOT EQUIPED WITH GSM / LTE / WIFI modules, please order them separately based on your needs. For WiFi you can also use WLE200NX, 600/900vx modules or MT7915 WiFi 6 modules, for GSM/LTE you can use Quectel or Sierra modules including latest CAT12, CAT20 modules and also new 5G modules Quectel RM520N-GL RM500Q, RM502Q, RM520N and RM510Q
• Supports 5GNR 5G modules Quectel, SIMCom & LTE CAT 3, 4, 6, 12, 16 and 16 LTE modules - it has fully support CAT12 or CAT16 Quectel latest LTE modem. EM16-G, EM20-G and EM12-G.
• it has all modules slots standalone (not shared !!!) 3 x MiniPCIE & 1 x M.2 (usb 3.0 protocol) interface Max 5000Gbps throughput.
• Tuned FirmWare from 5G LTE HW experts - We have customer test EM12 and EM20 in ATT, T-mobile and Sprint in US and many others, all work great

Hardware: MTK7621A board version 7 - Flash16M / RAM256M(CPU Cores:2 ;CPU MHz:880)

Learn More

COMPEX 5N17 5GHZ 17DBI DUAL-POLARIZATION ANTENNA element with 2*ufl

• 5.1 ~ 5.9 GHz
• 17 dBi Dual-Polarization
• 2x U.FL
• -40dB Isolation
• Antenna element + metal plate, also available in Weatherproof Enclosure (MJE-5N17 - optional)

Learn More

Dual Band 2×2 MU-MIMO 802.11ac/a/b/g/n Versatile Indoor Access Point

 

Learn More

Compex WPJ531HV-A Dual Radio Embedded Board gen3

WPJ531 is a powerful and robust wireless embedded board based on the Atheros AR9531 CPU.It features a 650MHz network processor and integrates a 2.4G 2x2 internal on-board radio and 1 miniPCIe slot that supports 802.11ac/abgn radio. Embedded with 64MB memory and 16MB Flash, WPJ531 provides the ideal platform for any applications. WPJ531 includes an integrated Power over Ethernet (PoE) that allows WPJ531 to be used in areas where power outlets are not readily available.
DC Power 1x DC Jack Connector: 24-56V
Power Over Ethernet 1x IEEE 802.3at or Passive PoE input minimum 36V
Power Consumption 7 Watts (Max)
SIM bay on board! Learn More

WPJ563-7A HV - Multi-function QCA9563 2.4GHz 3×3 MIMO Wireless Embedded Board with MiniPCI-e Slot and SIM card slot

Part no WPJ563 7A03PO16F1GAR-1
Lead time is 2-3 weeks now - available for orders now

775MHz CPU / 2x GE Port / 1x Mini PCIe / Designed for 802.11ac

• Qualcomm Atheros QCA9563 74Kc MIPS processor, Dragonfly Series
• 64KB I-Cache and 32 KB D-Cache, targeted to operate at 775MHz
• 128MB System Memory
• 16MB NOR Flash
• 3×3 On-board 2.4GHz radio, up to 450Mbps physical data rate
• Supports Dynamic Frequency Selection (DFS)
• Single SIM Holder on-board
• Support 2 x Gigabit Ethernet Port

Applications : 

• 802.11g/n + 802.11a/n/ac Access Point

• Point-to-MultiPoint High Capacity Wireless Bridge

• Wireless Customer-Premises Equipment (CPE)

WPJ563 board provide Mini_PCIE slot for 3G/4G module,.LTE supported frequencies/channels and LTE supported antenna are determined by the 3G/4G module.

Power solution :

DC Jack: 12-24V

PoE: IEEE 802.3af 48V,

IEEE 802.3at 56V,

or Passive PoE 36-56V DC

Learn More

MMJ531 is a high-performance Outdoor Access Point with integrated PoE. Using Qualcomm Atheros QCA9531 (650MHz)Processor, MMJ531 supports high-speed data transmission up to 300Mbps. MMJ531 is embedded with an integrated directional dual-polarization (vertical and horizontal) antenna supporting 2.4GHz (11dBi). The type of the antenna depends upon the order configuration.
Dual-polarization antenna provides good diversity coverage and better noise immunity. It has been integrated by high power radio to achieve longer range and higher throughput. The device is powerful, easy to handle, and also used in implementation over long distance by wireless ISP.

This AP is goint to be EOL - last unit in stock now.

Learn More

CompexWPJ531LV-A Dual Radio Embedded Board gen3 - available again, but MOQ is 50pcs - lead time is 2-3 weeks now

part no: WPJ531LV 7A07P01612AR-1 (no SIM slot)
WPJ531 is a powerful and robust wireless embedded board based on the Atheros AR9531 CPU.It features a 650MHz network processor and integrates a 2.4G 2x2 internal on-board radio and 1 miniPCIe slot that supports 802.11ac/abgn radio. Embedded with 64MB memory and 16MB Flash, WPJ531 provides the ideal platform for any applications. WPJ531 includes an integrated Power over Ethernet (PoE) that allows WPJ531 to be used in areas where power outlets are not readily available.

Learn More

MMZ531HV

Indoor 2,4GHz 11bgn access point with OMNI Payramid antena and POE support 802.3af

MMZ531 is a high-performance indoor Access Point with integrated PoE. Using Qualcomm Atheros QCA9531 network processor of speed 650MHz , coupled with 802.11bgn wireless technology and 2x2 MIMO technique enable it to support high-speed data transmission of up to 300Mbps.

DC Power 1x DC Jack Connector: 24-56V
Power Over Ethernet 1x IEEE 802.3at or Passive PoE input minimum 36V
Power Consumption 7 Watts (Max)
Learn More

indoor plastic BOX for WP54/WP543 router board + walmount kit + screws. not for wpj344 Learn More

Atheros AR7240 400MHz Network Processor - SALE - last 4 pcs in stock

1 Mini PCIe slot

2 Ethenet ports

Supports all Compex Mini PCIe radio modules

Supports Compex, OpenWRT firmware

Integrated passive Power-over-Ethernet

Integrated PoE cascade arrangement

Optional Remote hardware reset

Learn More

AVAILABLE !!! COMPEX power over ethernet , POE -100 220, injektor and extraktor, 3,3V up to 100m, fce: remote power/local power. The Compex Power Over Ethernet (POE-100-3.3) Kit is an accessory for the Compex Wireless Access Point, WPE54G. POE-100-3.3 allows the supply of operational power to a WPE54G via category 5 UTP cables. By deploying the POE-100-3.3, it removes the restriction of needing the Access Point to be close to a power supply. This means the Access Point can be used virtually anywhere. The POE-100-3.3 Kit consists of an injector unit and extractor unit and is an essential kit for outdoor or indoor wireless network deployment. Power Input 12V DC, 1.5A Power Output: 5V Ethernet Connector: RJ-45 Ethernet Data Rate: 10/100 Mbps Learn More