Antenna for LTE application: Fabry-Perot cavity (FPC) antenna
Connector Type I-Pex for IPEX MHF 4 connector 
Cable Type 1.13
Impedance 50Ω
Polarization Linea
Frequency 700-2700MHZ
VSWR <1.5
Peak gain (dBi) 8dBi
Cable length 12cm

LTE 5G 4G Antenna

• Designed for desktop/Laptop PCs that convert wireless M.2 Card to USB 3.0 port. Ideal for LTE 5G modules like RM500Q.
• You can insert your M.2 card (Socket 2 SSIC-base WWAN) such as GSM, HSPA(3.5G), GPS, LTE cards to this adapter then plug to USB port
• Supports USB interface of M.2 Cards (Socket 2 SSIC-base WWAN) such as 2G GSM, GPRS, 3G,CDMA, WLAN,WWLAN, HSPA MODEM , GPS, 4G WiMAX, LTE, Mini Card to desktop/Laptop PC, such as, Sierra Wireless , quectel, Simcom
• Support 30*42 type NGFF(M.2) Key B card
• Support SIM 6pin/8pin card connector.
• • Attention - can not support WiFi modules !

Specialy designed stable 3dB gain PUK omnidirection antenna for wild frequency range 700-2700 MHz for GSM 3G 4G or 5G use with LTE modules

Frequeny range: 700-2700 MHz

Bandwidth (MHz) 262/980MHZ

Input Impendence (Ω) 50

V.S.W.R ≤2 Gain (dBi) 3

Polarization Type Vertical polarization

Radiation Direction All (Omnidirectional)

Max Input Power (w) 50

Operating Temperature -20℃～+85℃

Storing Temperature -40℃～+85℃

Cable length (mm) 1000

Connector Type SMA

Dimension-mm Φ46*15

Advanced 802.11ac combo SoC - this module is EOL - you can use Intel AC7265 module as substitue 

Advanced 802.11ac features such as MU-MIMO, Host wake-on-wireless and ARP (Address Resolution Protocol) offloading enable the WLAN link to remain associated for extended periods for additional power savings

Supports dual-mode Bluetooth 5  - QCA9377 supports Bluetooth for Class-1 and Class-2 transmissions without requiring an external power amplifier Advanced WLAN/Bluetooth coexistence and concurrent RX WLAN/Bluetooth coexistence allows for superior rateover-range throughput and low-latency performance in real-world operating conditions Power saving techniques for low power consumption

Both WLAN and Bluetooth power management utilize advanced power saving techniques such as: - gating clocks to idle or inactive blocks - voltage scaling - fast start and settling circuits - active duty cycles - processor frequency scaling

INDOOR DIPLEX FILTER DD 8711f

to split DATA and SAT+TV signal on the beginning of coax network and to divide SAT+TV and DATA signal before end TV (very low loss -1dB and very high signal separation)
or to realise BY PASS of an existing aplifier in your coax network.
This solution is designed for TV / DVB-T2 cabling network with SATELITE signal coexistence
high quality housing with 3* F connectors
high isolation
low price

Wodaplug ® Dual SIM 5G 5GNR 4G LTE-A dual modules Failover redundancy & Load balance Open Source router MTK7621 board HW version 7 and higher, 4x LAN 1xWAN, 12 antenna ports, standalone: 1xM.2 USB3, 3xMiniPCIe, H721v5G can support 11ac WiFi (11ac 600VX or 900VX module ready, MT7915 based 11ax WiFi 6 modules supported in new firmware). New version 7 comes with 2.4G wifi module (Transytem TWL-2301H TWL-103  - Based on Atheros AR9590 3x3 MIMO Platform).

The H721 v5G Dual sim 5G LTE router with 4 standalone modules slots has been a great choice for custom builds and applications.  The router board’s (PCB) built in 1x M.2 slot for LTE modem and 2x SIM Card slots, makes it a great fit for our line of Sierra Wireless  Quectel M.2 modems. Also have 3 x Minipcie slots, 1 x for aditional modem (it is our M.2 B-Key adapter compatible) and 2 x more for your old standard modem (save your investment) or new one smoking gun in wifi world like 600vx / 900vx QCA9880 miniPCIe modules and WiFi 6 MT 7915/ 7916 modules (in new X-WRT firmeare).

Our new inventory of H721 v5G routers were special ordered to better accommodate our customer’s needs. New improved 5G ready version 7! Once again, if you want to have all info about ETA, versions,etc pls check our facebook page for news !

The H721 v5G now includes:

• 4 x 5G LTE Antennas + 4 x MHH4 pigtails for LTE modules pre-installed
• 3 x WiFi  Antennas + 3 x U.FL to SMA Bulkhead Antenna Connector Pigtails (pre-installed). 
• 2,4GHz WiFi 802.11n miniPCIe module (Transytem TWL-2301H TWL-103 - Based on Atheros AR9590 3x3 MIMO Platform ) - you can install second wifi module for dual radio application
• 12 Volt 2Amp Power Adapter
• 6 x Screws, Spacers/Nuts to mount M.2 LTE modem
• Wall mounts, screws and lags
• Cat5e Ethernet Cable
• THIS ROUTER IS NOT EQUIPED WITH GSM / LTE / WIFI modules, please order them separately based on your needs. For WiFi you can also use WLE200NX, 600/900vx modules or MT7915 WiFi 6 modules, for GSM/LTE you can use Quectel or Sierra modules including latest CAT12, CAT20 modules and also new 5G modules Quectel RM520N-GL RM500Q, RM502Q, RM520N and RM510Q
• Supports 5GNR 5G modules Quectel, SIMCom & LTE CAT 3, 4, 6, 12, 16 and 16 LTE modules - it has fully support CAT12 or CAT16 Quectel latest LTE modem. EM16-G, EM20-G and EM12-G.
• it has all modules slots standalone (not shared !!!) 3 x MiniPCIE & 1 x M.2 (usb 3.0 protocol) interface Max 5000Gbps throughput.
• Tuned FirmWare from 5G LTE HW experts - We have customer test EM12 and EM20 in ATT, T-mobile and Sprint in US and many others, all work great

Hardware: MTK7621A board version 7 - Flash16M / RAM256M(CPU Cores:2 ;CPU MHz:880)

Quectel RM510Q-AE is a 5G module that is specially optimized for IoT/eMBB applications. Adopting 3GPP Release 15, it supports both 5G NSA and SA modes. Designed in M.2 form factor, RM510Q-GL can be easily embedded in customers’ applications.

Wodaplug H721 5G routers can support this brand new modules !

Full part no : RM510QGLHA-M20-SGASA

Telit FN980 5G wireless module Specifications:

* Telit 5G Module

* Chipset: Qualcomm Snapdragon X55 5G

* 5G Sub-6 and mm Wave FDD and TDD, SA & NSA operations

* 5G core network Opt. 3a/3x and Opt. 2

* 4G: 7CA, up to 20 layers DL / 3CA UL,256 QAM DL/UL

* 3G: HSPA+ Rel. 8 (DL/UL 42/11 Mbps)

* Data Rates:

- 5G up to 5.5 Gbps DL/2.7 UL Gbps
- 4G up to 2.4 Gbps DL/211 Mbps UL
- 3G up to 42 DL/11 UL Mbps

* GNSS: gpsOne Gen9 L1 band on dedicated RF connector, L5 shared with cellular

* Voice support: VoLTE, VoNR (under evaluation), PCM audio over USB

* 4 antenna connectors for LTE/Sub-6

* 5G FR1 Bands: n1, n2, n3, n5, n7, n12, n14, n20, n28, n30, n41, n66, n71, n77, n78, n79

* 5G FR2 Bands: n257, n258, n260, 261

* LTE Bands: 1, 2, 3, 4, 5, 8, 9, 12, 13, 14, 17, 18, 19, 20, 26, 28, 71, 25, 66, 39, 29 (DL), 30, 32, 7, 38, 40, 41, 42, 43, 46 (LAA), 48(CBRS), 34, 27

* WCDMA Bands: 5, 8, 3, 4, 2, 1, 9, 19

* 5G 4x4 MIMO support on bands n1, n2, n7, n66, n3, n77, n78, n79, n41 and n30

* 4G 4x4 MIMO support on bands 32, 4, 66, 3, 2, 25, 1, 30, 40, 41, 7, 43, 42, 46, 48

* Interfaces
- 1.8/3 V SIM Interface
- USB 3.1 gen2 and 2.0
- PCIe gen3
- Drivers support: Windows 10, Linux

* Chipset: Qualcomm® Snapdragon™ X55

* Electrical & Sensitivity
- LTE/5G sub 6 Output power: -23 dBm (power class 3)
- Supply voltage: - Nominal: 3.3 VDC

* Antenna types: 4x LTE/Sub-6 + 4x QTM525/527

* FOTA Support

* Operating temperature range: -40°C to +85°C

* Dimensions: 30 x 50 x 3.5mm

* Approvals
- RED (planned)
- GCF (planned)
- Others (under evaluation)

The AirPrime® EM9190 M.2 from Sierra Wireless is an Embedded 5G NR and LTE Cat-22 Module that supports Sub-6 GHz and mm-Wave bands. This device is a part of the Sierra EM Series that offers global 5G connectivity. It delivers up to 5.5 Gbps of downlink speed and up to 330 Mbps of uplink speed.

The EM9190 device is available in a 30 x 52 x 2.38 mm footprint. With automatic 4G and 3G fallback networks, and a built-in GNSS receiver, it can be used for a wide range of M2M and IoT applications such as industrial routers, home gateways, industrial and consumer laptops, rugged tablet PCs, video surveillance and digital signage.

CHIPSET - Qualcomm SDX55 , M.2 form factor

Available for orders - leadtime is one - two weeks, em9190 are all like new in perfect working conditoon, has a few scratches on surface, tested & upgrade to latest fw.

xPON ONU Wodaplug ® FD504G-X-R410 4GE port, with EPON / GPON autodetect 

FD504G-X-R410 dual-mode ONU is one of the XPON optical network unit design to meet the requirement of the broadband access network.It apply in FTTH/FTTO to provide the data, video service based on the XPON network.

FD504G-X-R410 dual-mode ONU supports EPON and GPON two modes access. The ONU automatically switches into the corresponding PON mode by identifying the local OLT mode to complete GPON or EPON adaptive access.

FD504G-X-R410have a high reliability and provide quality of service guarantee, easy management, flexible expansion and networking. Itfully meets the ITU-T and IEEE technical standards and have good compatibility with third party OLT.

SC/UPC single mode single fiber 

GPON：FSAN G.984.2 standard, Class B+ 

EPON：1000BASE-PX20+ symmetric 

GPON：2.488Gbps/1.244Gbps downstream/upstream 

EPON：1.25Gbps downstream/upstream

C-DATA 4 PON GEPON OLT – FD1204SN WITH 2*10GB UPLINK AND L3 FEATURES

FD1204SN series provides 1 USB interface, 4 uplink combo interface, 2*10Gb uplink interface, and 4/8/16 EPON ports for downstream. It can support 256 ONUs under 1:64 splitter ratio.

Pizza-Box OLT series products is 1U high 19 inch rack mount product. The features of the OLT are small, convenient, flexible, easy to deploy, high performance. It is appropriate to deploy in an compact room environment.The OLT can use for “Triple-Play”, CPN, IP Camera, Enterprise LAN and IOT applications. It is a high  performance products.

MAIN FEATURES

Sierra Wireless 5G Module

* 5G Category: 5G NR Sub-6
* 5G DL 4.5Gbps, UL 660Mbps
* Satellite Systems: Galileo, Glonass, GPS, Beidou (Bands: L1 and L5)
* Firmware: Secure boot, Pre-certified firmware
* Dual SIM single standby (DSSS) switches

USB 3.0 dongle - total New design for latest 5Gnr M.2 Modem  Sierra wireless EM9190 EM9191 EM7690; Telit FN980 ; Thales MV31-W, Quectel  & Simcom Modem.

• Support 52mm,50mm,42mm length  three size of 5G M.2 Modem.
• Introduce integrated aluminum heat sink，make your 5G modem always cool.
• Add New switch for Sierra Wireless EM9190 EM9191 EM7690, switch will let modem work at USB mode.
• 2 Step electric capacity at Output side,(input 16V 220μF,output 16V 220μF+6.3V 820μF)
• Adjust output to 3.7V. Prevent voltage drop when high data transfer .
• Add 5V DC AUX port, Max support 5V 4A power adapter, provider 20W power for 5G modem.
• Use Nano SIM card slot , support hot swap simcard.
• ESD prtection at USB and SIM slot.
• Better performance, because of fast thermal module

Wodaplug ® High performance Dual SIM 5G 5GNR 4G LTE-A dual modules Failover redundancy & Load balance router MTK7621 board HW version 7 with switch to support Sierra EM919x and EM7690 modems, 4x LAN 1xWAN, 12 antenna ports, standalone: 1xM.2 USB3, 3xMiniPCIe, H721v5G can support 11ac WiFi (11ac 600VX or 900VX module ready, 11ac wave 2 QCA 9984, 9886 modules supported in new firmware). New version 7 comes with 2.4G wifi module (Transytem TWL-2301H TWL-103  - Based on Atheros AR9590 3x3 MIMO Platform). New X-WRT high performance firmware ! OpenWRT support.

The H721 v5G Dual SIM 5G LTE router with 4 standalone modules slots has been a great choice for custom builds and applications.  The router board’s (PCB) built in 1x M.2 slot for LTE modem and 2x SIM Card slots, makes it a great fit for our line of Sierra Wireless  Quectel M.2 modems. Also have 3 x Minipcie slots, 1 x for aditional modem (it is our M.2 B-Key adapter compatible) and 2 x more for your old standard modem (save your investment) or new one smoking gun in wifi world like 600vx / 900vx QCA9880 miniPCIe modules and lates WiFi6 modules MT7915 / MT7916 (in X-WRT firmware).

Our new inventory of H721 v5G routers were special ordered to better accommodate our customer’s needs. New improved 5G ready version 7! Once again, if you want to have all info about ETA, versions,etc pls check our facebook page for news !

The H721 v5G version 7 now includes:

• 4 x MHH4 pigtails for LTE modules pre-installed (4G or 5G LTE Antennas please order separately - we recommend Pulse Larsen W5095X)
• 2,4GHz WiFi 802.11n miniPCIe module (Transytem TWL-2301H TWL-103 - Based on Atheros AR9590 3x3 MIMO Platform ) - you can install second wifi module for dual radio application
• 3 x WiFi  Antennas + 3 x U.FL to SMA Bulkhead Antenna Connector Pigtails (pre-installed. you can install more WiFi antennas in) . 
• 12 Volt 2Amp Power Adapter
• 6 x Screws, Spacers/Nuts to mount M.2 LTE modem
• Wall mounts, screws and lags
• Cat5e Ethernet Cable
• THIS ROUTER IS NOT EQUIPED WITH GSM / LTE modules, please order them separately based on your needs. For WiFi you can also use 524WiFi 600/900vx modules, for GSM/LTE you can use Quectel or Sierra modules including latest 5G CAT20, CAT16, CAT12 modules and also new 5G modules Quectel RM520N-GL RM500Q , RM502Q, RM510Q and Sierra wireless EM919x EM7690 in USB 3.0 mode. 
• Supports 5GNR 5G modules Quectel, Sierra Wireles, Thales, SIMCom & LTE CAT 3, 4, 6, 12, 16 and 20 LTE modules - it has fully support CAT12 or CAT16 Quectel latest LTE modem. EM16-G, EM20-G and EM12-G.
• it has all modules slots standalone (not shared !!!) 3 x MiniPCIE & 1 x M.2 (usb 3.0 protocol) interface Max 5000Gbps throughput.
• Tuned FirmWare from 5G LTE HW experts - We have customer test EM12 and EM20 in ATT, T-mobile and Sprint in US and many others, all work great

Hardware: MTK7621A board version 7 - Flash16M / RAM256M(CPU Cores:2 ;CPU MHz:880)